Previous  Up  Next

Module Unix_syscalls.Terminal_io

module Terminal_io: sig .. end
type t = Core.Std.Caml.Unix.terminal_io = {
   mutable c_ignbrk :bool; (*Ignore the break condition.*)
   mutable c_brkint :bool; (*Signal interrupt on break condition.*)
   mutable c_ignpar :bool; (*Ignore characters with parity errors.*)
   mutable c_parmrk :bool; (*Mark parity errors.*)
   mutable c_inpck :bool; (*Enable parity check on input.*)
   mutable c_istrip :bool; (*Strip 8th bit on input characters.*)
   mutable c_inlcr :bool; (*Map NL to CR on input.*)
   mutable c_igncr :bool; (*Ignore CR on input.*)
   mutable c_icrnl :bool; (*Map CR to NL on input.*)
   mutable c_ixon :bool; (*Recognize XON/XOFF characters on input.*)
   mutable c_ixoff :bool; (*Emit XON/XOFF chars to control input flow.*)
   mutable c_opost :bool; (*Enable output processing.*)
   mutable c_obaud :int; (*Output baud rate (0 means close connection).*)
   mutable c_ibaud :int; (*Input baud rate.*)
   mutable c_csize :int; (*Number of bits per character (5-8).*)
   mutable c_cstopb :int; (*Number of stop bits (1-2).*)
   mutable c_cread :bool; (*Reception is enabled.*)
   mutable c_parenb :bool; (*Enable parity generation and detection.*)
   mutable c_parodd :bool; (*Specify odd parity instead of even.*)
   mutable c_hupcl :bool; (*Hang up on last close.*)
   mutable c_clocal :bool; (*Ignore modem status lines.*)
   mutable c_isig :bool; (*Generate signal on INTR, QUIT, SUSP.*)
   mutable c_icanon :bool; (*Enable canonical processing (line buffering and editing)*)
   mutable c_noflsh :bool; (*Disable flush after INTR, QUIT, SUSP.*)
   mutable c_echo :bool; (*Echo input characters.*)
   mutable c_echoe :bool; (*Echo ERASE (to erase previous character).*)
   mutable c_echok :bool; (*Echo KILL (to erase the current line).*)
   mutable c_echonl :bool; (*Echo NL even if c_echo is not set.*)
   mutable c_vintr :char; (*Interrupt character (usually ctrl-C).*)
   mutable c_vquit :char; (*Quit character (usually ctrl-\).*)
   mutable c_verase :char; (*Erase character (usually DEL or ctrl-H).*)
   mutable c_vkill :char; (*Kill line character (usually ctrl-U).*)
   mutable c_veof :char; (*End-of-file character (usually ctrl-D).*)
   mutable c_veol :char; (*Alternate end-of-line char. (usually none).*)
   mutable c_vmin :int; (*Minimum number of characters to read before the read request is satisfied.*)
   mutable c_vtime :int; (*Maximum read wait (in 0.1s units).*)
   mutable c_vstart :char; (*Start character (usually ctrl-Q).*)
   mutable c_vstop :char; (*Stop character (usually ctrl-S).*)
} 
type setattr_when = Core.Std.Caml.Unix.setattr_when =
| TCSANOW
| TCSADRAIN
| TCSAFLUSH 
val tcgetattr : Fd.t -> t Import.Deferred.t
val tcsetattr : t ->
       Fd.t -> mode:setattr_when -> unit Import.Deferred.t