Module Terminal_io

type t = Core.Std.Caml.Unix.terminal_io = {

mutable c_ignbrk	: bool	;	(*	Ignore the break condition.	*)
mutable c_brkint	: bool	;	(*	Signal interrupt on break condition.	*)
mutable c_ignpar	: bool	;	(*	Ignore characters with parity errors.	*)
mutable c_parmrk	: bool	;	(*	Mark parity errors.	*)
mutable c_inpck	: bool	;	(*	Enable parity check on input.	*)
mutable c_istrip	: bool	;	(*	Strip 8th bit on input characters.	*)
mutable c_inlcr	: bool	;	(*	Map NL to CR on input.	*)
mutable c_igncr	: bool	;	(*	Ignore CR on input.	*)
mutable c_icrnl	: bool	;	(*	Map CR to NL on input.	*)
mutable c_ixon	: bool	;	(*	Recognize XON/XOFF characters on input.	*)
mutable c_ixoff	: bool	;	(*	Emit XON/XOFF chars to control input flow.	*)
mutable c_opost	: bool	;	(*	Enable output processing.	*)
mutable c_obaud	: int	;	(*	Output baud rate (0 means close connection).	*)
mutable c_ibaud	: int	;	(*	Input baud rate.	*)
mutable c_csize	: int	;	(*	Number of bits per character (5-8).	*)
mutable c_cstopb	: int	;	(*	Number of stop bits (1-2).	*)
mutable c_cread	: bool	;	(*	Reception is enabled.	*)
mutable c_parenb	: bool	;	(*	Enable parity generation and detection.	*)
mutable c_parodd	: bool	;	(*	Specify odd parity instead of even.	*)
mutable c_hupcl	: bool	;	(*	Hang up on last close.	*)
mutable c_clocal	: bool	;	(*	Ignore modem status lines.	*)
mutable c_isig	: bool	;	(*	Generate signal on INTR, QUIT, SUSP.	*)
mutable c_icanon	: bool	;	(*	Enable canonical processing (line buffering and editing)	*)
mutable c_noflsh	: bool	;	(*	Disable flush after INTR, QUIT, SUSP.	*)
mutable c_echo	: bool	;	(*	Echo input characters.	*)
mutable c_echoe	: bool	;	(*	Echo ERASE (to erase previous character).	*)
mutable c_echok	: bool	;	(*	Echo KILL (to erase the current line).	*)
mutable c_echonl	: bool	;	(*	Echo NL even if c_echo is not set.	*)
mutable c_vintr	: char	;	(*	Interrupt character (usually ctrl-C).	*)
mutable c_vquit	: char	;	(*	Quit character (usually ctrl-\ ).	*)
mutable c_verase	: char	;	(*	Erase character (usually DEL or ctrl-H).	*)
mutable c_vkill	: char	;	(*	Kill line character (usually ctrl-U).	*)
mutable c_veof	: char	;	(*	End-of-file character (usually ctrl-D).	*)
mutable c_veol	: char	;	(*	Alternate end-of-line char. (usually none).	*)
mutable c_vmin	: int	;	(*	Minimum number of characters to read before the read request is satisfied.	*)
mutable c_vtime	: int	;	(*	Maximum read wait (in 0.1s units).	*)
mutable c_vstart	: char	;	(*	Start character (usually ctrl-Q).	*)
mutable c_vstop	: char	;	(*	Stop character (usually ctrl-S).	*)

}

type setattr_when = Core.Std.Caml.Unix.setattr_when =

| TCSANOW
| TCSADRAIN
| TCSAFLUSH